Choosing the right cargo body length for a crane truck comes down to one number you probably haven’t calculated yet: the payload you actually need to move after the crane and outriggers are bolted on. Most buyers start with the crane rating — 5-ton, 8-ton, 12-ton — and then pick a body that looks proportional. That sequence is backwards. The crane determines how much structural weight sits behind the cab, the body length determines how that weight is distributed across the frame and axles, and the two together decide whether you can legally carry the cargo the crane was bought to handle. Get the order right and the truck works for a decade. Get it wrong and you own a crane truck that is either overweight on the rear axle or too short to carry anything useful.
This guide walks through the engineering logic I use when matching cargo body length to crane size, chassis, and duty cycle. It is written for fleet managers, importers, and project buyers who need to specify a truck once and get it right.
Start With the Load, Not the Crane
Before anyone talks about body length, define the job in numbers. A crane truck is a compromise machine: every kilogram of crane, outrigger, subframe, and reinforcement is a kilogram you cannot spend on cargo. If you don’t know the cargo weight and dimensions first, you cannot size anything.
Write down these five items before contacting any supplier:
- Maximum single lift weight — the heaviest item the crane will pick up, not the average
- Jari-jari kerja horizontal — how far from the crane centerline that load must reach
- Ketinggian angkat — from ground level to the highest point of the lift
- Cargo weight per trip — the total payload the body must carry, independent of the crane lift
- Cargo dimensions — length, width, and stacking height of the longest or bulkiest item
These five numbers drive everything else. A crane that lifts 8 tonnes at 2.5 meters may only lift 2 tonnes at 8 meters — the load chart decides, not the badge on the boom. Buyers evaluating lifting capacity should compare the actual load chart before selecting a derek yang dipasang di truk, because the nominal tonnage tells you almost nothing about real-world capacity at working radius.
How Crane Size Eats Into Cargo Body Length
A truck-mounted crane is not a small accessory. Depending on class, the crane assembly, base, outrigger beams, and reinforcement typically add somewhere in the range of 1.5 to 4 tonnes to the chassis, and the outrigger footprint forces the body to start further back from the cab. That has two direct consequences for body length.
First, the crane occupies frame real estate. A crane mounted behind the cab pushes the cargo body rearward, which means either a shorter body or a longer wheelbase — and a longer wheelbase means a larger turning circle and different axle loading. Second, the outrigger beams need clear space to deploy. If the body overhangs the outrigger mounting area, the crane cannot be used safely.
The practical rule: as crane class increases, body length shrinks unless you step up to a longer chassis. A 5-ton crane on a 4×2 chassis might allow a 5.5 to 6.5 meter body. A 12-ton crane on the same chassis forces the body down to 4.5 to 5.5 meters, or the truck must move to a 6×4 with a longer frame to recover the lost cargo length.
Typical Body Length Ranges by Chassis and Crane Class
| Konfigurasi Sasis | Crane Class (nominal) | Indicative Cargo Body Length | Paling Cocok Untuk |
|---|---|---|---|
| 4×2, medium duty | 3–5 tonne | 5.0–6.5 m | Urban delivery, light construction support |
| 4×2, heavy duty | 5–8 tonne | 4.5–6.0 m | Municipal service, equipment transport |
| 6×4, heavy duty | 8–12 tonne | 6.0–7.5 m | Construction, utility, industrial delivery |
| 6×4, heavy duty | 12–16 tonne | 5.5–7.0 m | Heavy equipment, precast concrete |
| 8×4, heavy duty | 12–20 tonne | 7.0–9.0 m | Long-length cargo, structural steel |
These are indicative ranges only. Final body length must be confirmed against the specific chassis wheelbase, the crane mounting drawing, and the destination-country axle and overall length limits. Two trucks with the same nominal configuration from different suppliers can end up with different usable body lengths because of how the subframe and outrigger boxes are laid out.
The Weight Balancing Act: Crane, Body, and Payload
Here is where most specifications fail. The conversation usually goes: “I want a 10-tonne crane and a 7-meter body.” Nobody checks whether the resulting truck can carry a legal payload. Run the arithmetic and the answer is often no.
Consider the weight stack on a typical 6×4 crane truck:
- Chassis curb weight: a substantial base figure before anything is added
- Crane assembly, base, and outriggers: 2–4 tonnes depending on class
- Reinforced subframe and body: 1.5–3 tonnes depending on length and steel grade
- Fuel, driver, tools, and accessories: several hundred kilograms
Subtract that from the gross vehicle weight rating and you get the remaining payload. On a mid-range 6×4, adding a 12-tonne crane and a 7-meter body can leave you with a cargo payload that is smaller than the crane itself can lift. That is not a design failure — it is physics. The crane lifts a load for a few minutes; the body carries a load for hours. You have to decide which matters more.
Payload vs. GVW vs. Legal Weight — Three Different Numbers
Buyers routinely confuse three figures that mean completely different things:
- Body volume or body length — how much space the cargo occupies. Tells you nothing about weight.
- Technical payload — what the chassis, axles, and tires can physically support. This is the engineering limit.
- Muatan sah — what the destination country allows on the road, based on axle weight limits, total weight limits, and registration category.
The smallest of the three governs. A truck that can technically carry 12 tonnes may be legally limited to 8 tonnes on the road, and the body may be sized for a cargo that weighs 15 tonnes. Only the legal figure matters for daily operation. Buyers should confirm axle-weight and gross-weight limits with the destination authority before finalizing body length, because a longer body encourages heavier loading — and heavier loading is exactly what enforcement officers check.
Matching Body Length to the Cargo Itself
Body length is not just a weight question. It is also a fit question. If the cargo is 6 meters of steel pipe, a 5.5-meter body does not work regardless of what the load chart says. If the cargo is palletized and stacked, a shorter body with higher sidewalls may be more efficient than a long flat deck.
Work through the cargo geometry:
- Long, rigid items (pipe, beams, precast sections) — body length must exceed the cargo length, or the cargo overhangs and creates axle-loading problems
- Palletized or crated goods — body length should match the pallet module, usually 1.2 m or 1.0 m increments, to avoid wasted floor space
- Bulk or loose material — body volume matters more than length; a shorter, deeper body may carry more than a long, shallow one
- Mixed loads — the body must accommodate the longest item, but the crane must handle the heaviest
There is also a stability dimension. A very long body with a heavy crane mounted forward shifts the center of gravity and can make the truck light on the front axle when unloaded, or overload the rear axle when loaded. The correct body length is the one that keeps the loaded center of gravity inside the wheelbase envelope, not the longest body that physically fits.
Chassis and Axle Configuration: The Foundation Under the Body
Body length decisions cannot be separated from the chassis. The wheelbase, frame section height, frame material, and axle ratings all constrain what the body builder can do.
4×2 vs. 6×4 vs. 8×4 for Crane Truck Bodies
| Konfigurasi | Typical Body Length | Crane Class Practical Limit | Keunggulan Utama | Keterbatasan Utama |
|---|---|---|---|---|
| 4×2 | 4.5–6.5 m | Up to ~8 tonnes | Lower cost, tighter turning, easier urban access | Limited rear axle capacity, shorter frame |
| 6×4 | 6.0–7.5 m | Up to ~16 tonnes | Better weight distribution, higher legal payload | Longer wheelbase, higher tire cost |
| 8×4 | 7.0–9.0 m | Up to ~20 tonnes | Highest payload and longest cargo capacity | Heaviest curb weight, largest turning circle |
For fleet operators, the trade-off is straightforward. A 6×4 gives you more legal payload and better stability with a heavy crane, but it costs more to buy, more to fuel, and more to tire. An 8×4 stretches body length further but adds curb weight that eats into the payload gain. There is no universally correct answer — only the configuration that matches your cargo, route, and legal environment.
Buyers who need to understand how different chassis and body combinations are built for construction and industrial work can review the platform options in the solusi kendaraan konstruksi untuk tugas berat range, which shows how frame length and axle layout interact with body design.
Crane Mounting Position and Its Effect on Body Length
Where the crane sits on the frame changes how much body you can fit. There are three common layouts:
Behind the Cab
The crane is mounted immediately behind the cab, with the cargo body behind it. This gives the crane the best lifting geometry and keeps the load close to the truck’s center of gravity. The cost is body length — the crane assembly and its base consume frame space that would otherwise carry cargo. This layout suits operations where lifting is the primary task and cargo volume is secondary.
Rear Mounted
The crane sits at the rear of the frame, behind the cargo body. This preserves maximum body length and is common on trucks that carry long cargo. The trade-off is that the crane’s lifting envelope is at the very back of the truck, which can be awkward for loading from the side and can make the rear axle very heavy. Rear mounting also requires careful attention to approach and departure angles.
Mid-Mounted or Offset
Some designs place the crane between the cab and body, or offset to one side, to balance lifting reach with cargo capacity. These layouts are more complex, require custom subframe work, and are usually specified when the duty cycle demands both lifting and significant cargo volume. They are not off-the-shelf configurations.
The mounting position is decided at the specification stage. Changing it later means rebuilding the subframe and re-certifying the axle loads. Get it right the first time.
Duty Cycle: How the Truck Actually Works Every Day
Body length should reflect the operating cycle, not the showroom. Ask how many lifts per day, how many trips, and how the truck interacts with loading equipment.
- High-lift, low-mileage (equipment installation, precast placement) — prioritise crane capacity and stability; body length can be shorter
- Low-lift, high-mileage (utility delivery, material distribution) — prioritise body length and payload; a smaller crane may be sufficient
- Mixed duty — the hardest case; you need a balanced specification and must accept that neither the crane nor the body will be optimal
Loading method also matters. If cargo is loaded by forklift from the side, the body must have the right deck height and the outrigger beams must not block access. If cargo is loaded by the crane itself, the body length must allow the boom to reach the far end of the deck without exceeding the load chart. A body that is one meter too long can put the far end of the deck outside the crane’s safe working envelope at full extension.
Maintenance and Uptime Considerations
Longer bodies and larger cranes mean more hydraulic components, more pivot points, and more stress on the frame. Plan maintenance around the actual configuration:
- Crane slew ring, pins, and bushings — inspect for wear and lubrication condition
- Outrigger beams and cylinders — check for bending, seal leaks, and pad condition
- Body subframe and mounting bolts — check for cracking at stress points, especially where the body meets the crane base
- Hydraulic oil and filters — contamination is the most common cause of slow or erratic crane operation
- Rear axle and suspension — a crane truck’s rear axle works harder than a standard cargo truck’s
Downtime on a crane truck is expensive because the truck is often the only lifting asset on site. Spare parts availability for the crane, the hydraulic system, and the chassis should be confirmed before purchase, not after the first failure. Buyers should also confirm that service documentation and parts catalogs are provided in a language the local workshop can use.
Total Biaya Kepemilikan: Lebih dari Sekadar Harga Beli
The purchase price is the smallest part of the story. A crane truck’s real cost is built from:
- Harga pembelian sasis dan derek
- Body fabrication and subframe reinforcement
- Biaya pengiriman, asuransi, dan bea masuk
- Fuel or energy over the operating life
- Tires — a crane truck typically runs heavier than a standard cargo truck
- Pemeliharaan terjadwal — mesin, transmisi, as roda, sistem hidraulik
- Unscheduled repairs — crane hydraulics, outriggers, body structure
- Downtime cost — lost revenue while the truck is off the road
- Nilai sisa saat dijual kembali atau ditukar tambah
A longer body may cost more upfront but reduce trips per day, lowering fuel and driver cost per tonne moved. A larger crane may cost more but eliminate the need to rent a separate lifting machine. Neither is automatically better. The correct choice is the one that minimises cost per unit of work delivered over the truck’s life — and that calculation depends entirely on your duty cycle.
For buyers comparing how different body and chassis configurations affect operating economics, the analysis in biaya operasional truk pengangkut per kilometer uses the same cost-per-unit framework that applies to crane trucks, even though the body type is different.
Kepatuhan dan Persyaratan Pasar Tujuan
Body length is not just an engineering decision — it is a regulatory one. Before finalizing a specification, confirm these items for the destination market:
- Maximum overall vehicle length — some jurisdictions limit total length, which caps body length once the cab and crane are counted
- Batas beban poros — front and rear axle limits determine how much crane and body weight you can legally carry
- Gross vehicle weight limits — the total legal weight, which governs payload
- Registration category — some countries classify crane trucks differently from standard cargo trucks
- Konfigurasi kemudi — left-hand or right-hand drive, which affects cab and frame layout
- Standar emisi — determines engine and aftertreatment, which affects chassis weight and cost
- Persyaratan penerangan dan penandaan — especially for vehicles that overhang or carry projecting loads
There is no single “global compliant” crane truck. Every market has its own combination of weight, dimension, emission, and registration rules. The final specification must be confirmed against the destination country’s requirements, and the buyer should obtain written confirmation of the applicable limits before signing a purchase order.
Cara Mengevaluasi Pemasok Truk Derek
When comparing suppliers, use a consistent framework rather than a single price number. The criteria that matter most are:
- Kemampuan teknik — can the supplier produce a body length and crane mounting drawing specific to your chassis and duty cycle, or only offer standard catalog configurations?
- Weight and axle-load calculation — does the quotation include a calculated payload and axle-load distribution, or just a body length?
- Crane integration — is the crane matched to the chassis and body as a system, or bolted on as a separate item?
- Dokumentasi — are load charts, maintenance manuals, and parts catalogs provided?
- Dukungan suku cadang — is there a parts plan for the crane, hydraulics, and chassis?
- Pengalaman di bidang ekspor — does the supplier understand shipping constraints for a truck with a mounted crane and long body?
- After-sales structure — who handles warranty and service in the destination market?
Chinese Truck Factory works within this framework by treating the crane truck as a complete system: chassis selection, crane mounting position, body length, axle-load calculation, and export documentation are handled together rather than as separate line items. Buyers can review the available configurations and request a specification matched to their duty cycle through the derek yang dipasang di truk range, and can see how the same integrated approach applies to other specialized platforms in the kendaraan khusus catalog.
For buyers who want to move from general research to a specific quotation, the most useful step is to prepare the five load numbers listed at the start of this guide, along with the destination country, port, and expected annual mileage. With those inputs, a supplier can calculate a realistic body length and payload rather than guessing.
Ajukan Permohonan Peninjauan Spesifikasi Truk Derek
Pertanyaan yang Sering Diajukan
How do I calculate the right cargo body length for my crane truck?
Start with the cargo dimensions and weight, then subtract the space consumed by the crane assembly, base, and outrigger beams. The remaining frame length is your maximum body length. Confirm that the resulting configuration still meets the destination country’s axle-weight and overall-length limits, and that the loaded center of gravity stays within the wheelbase envelope.
Does a bigger crane always mean a shorter cargo body?
Not always, but usually. A larger crane adds more structural weight and occupies more frame space, which reduces the length available for the body unless you move to a longer chassis. The correct approach is to size the crane from the lift requirement and then select the chassis that allows the body length the cargo requires.
What is the difference between technical payload and legal payload?
Technical payload is what the chassis, axles, and tires can physically support. Legal payload is what the destination country allows on the road. The legal figure is always the governing limit, and it is usually lower. Buyers must confirm axle-weight and gross-weight limits with the destination authority before finalizing the specification.
Can I mount a crane on any cargo truck chassis?
No. The chassis must have sufficient frame strength, the correct wheelbase for the crane and body layout, and axle ratings that can handle the combined weight. Mounting a crane on an unsuitable chassis creates axle overload, frame cracking, and stability problems that cannot be corrected by adding reinforcement later.
How does body length affect fuel consumption?
Body length itself has a modest effect, but the weight of the body and the cargo it carries has a significant one. A longer body adds curb weight, which reduces payload and increases fuel consumption per tonne moved. Actual fuel consumption depends on gross weight, route, speed, gradient, idling, and driver behavior, so a single figure cannot represent all operating conditions.
What should I include in a crane truck quotation request?
Provide the maximum lift weight, horizontal working radius, lifting height, cargo weight per trip, cargo dimensions, destination country and port, expected annual mileage, road conditions, drive configuration, steering side, emission requirement, and quantity. With these inputs, a supplier can calculate a realistic body length and payload instead of offering a standard catalog configuration.
Bagaimana cara pengiriman truk derek ke luar negeri?
Crane trucks are usually shipped by RoRo or breakbulk because of their height and the mounted crane. Some configurations can be shipped on flat racks. The choice depends on vehicle dimensions, weight, quantity, route, and destination port. Buyers should confirm the shipping method and any dismantling requirements before the truck is built.
The right cargo body length is not the longest one that fits, and the right crane is not the largest one available. It is the combination that carries your actual cargo, lifts your actual load at your actual working radius, stays within the legal weight and dimension limits of the destination market, and can be maintained with the parts and skills available locally. Buyers who define the duty cycle first — before comparing crane classes or body lengths — end up with a truck that earns its keep. Buyers who start with a crane rating and work backwards usually end up with a truck that is either overweight, under-length, or both.
